View B101EW05V0_5740885.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 ( v ) preliminary specifications ( ) final specifications module 10.1(10.07) wxga 16:10 color tft-lcd with led backlight design model name b101ew05 v0 (h/w:0a ) note led backlight with driving circuit design color management (virtual and rich color solution ) dynamic contrast ratio (power saving solution) customer date checked & approved by date note: this specification is subject to change without notice. approved by date ch lin 09/14/2010 prepared by yw lee 09/14/2010 nbbu marketing division au optronics corporation www..net
2 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 contents 1. handling precautions .............................................................. 4 2. general description................................................................. 5 2.1 general specification .......................... ................................................... ........................................ 5 2.2 optical characteristics........................ ................................................... ......................................... 6 3. functional block diagram ...................................................... 11 4. absolute maximum ratings ................................................... 12 4.1 absolute ratings of tft lcd module............. ................................................... ..........................12 4.2 absolute ratings of touch sensor ............... ................................................... ...............................12 4.3 absolute ratings of environment ................ ................................................... ...............................12 5. electrical characteristics ....................................................... 13 5.1 tft lcd module ................................. ................................................... .....................................13 5.3 backlight unit ................................. ................................................... ...........................................15 6. signal interface characteristic .............................................. 16 6.1 pixel format image ............................. ................................................... .......................................16 6.2 the input data format.......................... ................................................... .....................................17 6.3 integration interface requirement .............. ................................................... ................................18 6.4 interface timing ............................... ................................................... ..........................................20 6.5 power on/off sequence .......................... ................................................... ................................21 7. panel reliability test............................................................. 22 7.1 vibration test................................. ................................................... ............................................22 7.2 shock test ..................................... ................................................... ............................................22 7.3 reliability test ............................... ................................................... ............................................22 8. mechanical characteristics .................................................... 23 8.1 lcm outline dimension .......................... ................................................... ..................................23 9. shipping and package ........................................................... 25 9.1 shipping label format .......................... ................................................... .....................................25 9.2 carton package................................. ................................................... .........................................26 9.3 shipping package of palletizing sequence ....... ................................................... ...........................26 10. appendix ............................................................................. 27 10.1 edid description .............................. ................................................... ......................................27 www..net
3 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 record of revision version and date page old description new description remark 0.1 2010/09/14 all first edition for customer www..net
4 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interf ace connector, be sure not to rotate nor tilt the interface connector of the tft module. 11)after installation of the tft module into an enc losure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source (iec60950 or ul1950), or be applied exemptio n. 13) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, connector s and led circuit part of tft module that a led light bar build in as a light sou rce of back light unit. it can prevent electrostic breakdown. www..net
5 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 2. general description b101ew05 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the screen format is intended to support the 16:10 wxga, 1280(h) x800(v) screen and 262k col ors (rgb 6-bits data driver) with led backlight driving circuit. all input signals ar e lvds interface compatible. b101ew05 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 255.85 (10.07w) active area [mm] 216.96(h) x 135.6(v) pixels h x v 1280 x 3(rgb) x 800 pixel pitch [mm] 0.1695 x 0.1695 pixel format r.g.b. vertical stripe display mode normally black white luminance (i led =19ma) (note: iled is led current) [cd/m 2 ] 350 typ. (5 points average) 297 min. (5 points average) luminance uniformity 1.25 max. (5 points) contrast ratio 1500 typ, 1000 min. response time [ms] 25 typ / 35 max nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 3.4 max. (include logic and blu power) weight [grams] 180 max. min. typ. max. length 228.96 229.46 229.95 width 148.7 149.2 149.7 panel only physical size without bracket [mm] thickness - -- - - - 5.2 electrical interface 1 channel lvds glass thickness [mm] 0.3 surface treatment anti-reflection Q 1.5%, hardness 3h support color 262k colors ( rgb 6-bit ) www..net
6 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 temperature range operating storage (non - operating) [ o c] [ o c] 0 to +50 - 20 to +60 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item symbol conditions min. typ. max. unit note white luminance i led =19ma 5 points average 297 350 --- cd/m 2 1, 4, 5. r l horizontal (right) cr = 10 (left) 85 85 89 89 --- --- viewing angle h l vertical (upper) cr = 10 (lower) 85 85 89 89 --- --- degree 4, 9 luminance uniformity 5p 5 points --- --- 1.25 1, 3, 4 luminance uniformity 13p 13 points --- --- 1.50 2, 3, 4 contrast ratio cr 1000 1500 - 4, 6 cross talk % --- --- 4 4, 7 response time t rt rising + falling --- 25 35 msec 4, 8 rx tbd red ry tbd gx tbd green gy tbd bx tbd blue by tbd wx 0.283 0.313 0.343 color / chromaticity coodinates white wy 0.299 0.329 0.359 ntsc % cie 1931 - 45 - 4 www..net
7 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 note 1 : 5 points position (ref: active area) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2 : 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3 : the luminance uniformity of 5 or13 points is defi ned by dividing the maximum luminance values by the minimum test point luminance note 4 : measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
8 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 lighting backlight for 30 minutes in a stable, wind less and dark room, and it should be measured in th e center of screen. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. note 7 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 contrast rati o (cr)= brightness on the white state brightness on the black state www..net
9 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 note 8 : definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to fig ure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
10 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 note 9 . definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal an d 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www..net
11 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 3. functional block diagram the following diagram shows the functional block of the 10.1 inches wide color tft/lcd 40 pin one channel module www..net
12 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 4. absolute maximum ratings an absolute maximum rating of the module is as foll owing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of touch sensor item symbol min max unit conditions touch sensor power voltage vin 3.1 6 [volt] 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 4 operation humidity hop 5 95 [%rh] note 4 storage temperature tst -20 +60 [ o c] note 4 storage humidity hst 5 95 [%rh] note 4 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to au o iis (incoming inspection standard). twb=39c operating range storage range www..net
13 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; the power specification are measured under 25 and frame frenquency under 60hz symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - - 0.75 [watt] note 1 idd idd current - - 240 [ma] note 1 irush inrush current - - 2000 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition black pattern at 3.3v driving voltage. (p max =v 3.3 x i black ) note 2 measure condition 90% 10% vin rising time 0v 3.3v 0.5ms www..net
14 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit v th differential input high threshold (vcm=+1.2v) --- 100 [mv] v tl differential input low threshold (vcm=+1.2v) -100 ---- [mv] |v id | differential input voltage 100 600 [mv] v cm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform www..net
15 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 5.3 backlight unit 5.3.1 led characteristics parameter symbol min typ max units condition backlight power consumption pled - - 2.4 [watt] (ta=25 ), note 1 vin =12v led life-time n/a 15,000 - - hour (ta=25 ), note 2 i f =19ma note 1: calculator value for reference p led = v f (normal distribution) * i f (normal distribution) / efficiency note 2: the led life-time define as the estimated time to 50% degradation of initial luminous. 5.3.2 backlight input signal characteristics parameter symbol min typ max units remark led power supply vled 5.5 12.0 21.0 [volt] led enable input high level 2.5 - 5.5 [volt] led enable input low level vled_en - - 0.8 [volt] pwm logic input high level 2.5 - 5.5 [volt] pwm logic input low level vpwm_en - - 0.8 [volt] pwm input frequency fpwm 100 - 1k hz pwm duty ratio duty 5 -- 100 % define as connector interface (ta=25 ) www..net
16 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 6. signal interface characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. www..net
17 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note: output signals from any system shall be low o r high-impedance state when vdd is off. www..net
18 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 6.3 integration interface requirement 6.3.1 connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. connector name / designation for signal connector manufacturer jae or compatible type / part number jae hd1s040ha1 or compatible mating housing/part number ipex 20453-040t-11or com patible 6.3.2 pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin# signal name description 1 nc no connection (reserve) 2 avdd power supply +3.3v 3 avdd power supply +3.3v 4 vedid edid +3.3v power 5 nc no connection (reserve) 6 clk_edid edid clock input 7 dat_edid edid data input 8 rin0- -lvdsdifferential data input(r0-r5,g0) 9 rin0+ +lvdsdifferential data input(r0-r5,g0) 10 gnd ground 11 rin1- -lvdsdifferential data input(g1-g5,b0-b1) 12 rin1+ +lvdsdifferential data input(g1-g5,b0-b1) 13 gnd ground 14 rin2- -lvdsdifferential data input(b2-b5,hs,vs ,de) 15 rin2+ +lvdsdifferential data input(b2-b5,hs,vs, de) 16 gnd ground 17 clkin- -lvdsdifferential clock input 18 clkin+ +lvdsdifferential clock input 19 gnd groundCshield 20 nc no connection (reserve) 21 nc no connection (reserve) 22 gnd groundCshield 23 nc no connection (reserve) www..net
19 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 24 nc no connection (reserve) 25 gnd groundCshield 26 nc no connection (reserve) 27 nc no connection (reserve) 28 gnd groundCshield 29 nc no connection (reserve) 30 nc no connection (reserve) 31 vled_gnd led ground 32 vled_gnd led ground 33 vled_gnd led ground 34 nc no connection (reserve) 35 vpwm_en system pwm logic input level 36 vled_en led enable input level 37 dcr_en dcr enable input level 38 vled led power supply 39 vled led power supply 40 vled led power supply note1: input signals shall be low or high-impedance state when vdd is off. pin 1 connector pin 40 www..net
20 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x 800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate --- --- 60 --- hz clock frequency 1/ t clock 64 68.93 85 mhz period t v 808 816 1023 active t vd 800 vertical section blanking t vb 8 16 223 t line period t h 1310 1408 2047 active t hd 1280 horizontal section blanking t hb 40 168 767 t clock note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
21 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 6.5 power on/off sequence power on/off sequence is as follows. interface sign als and led on/off sequence are also shown in the chart. signals from any system shall be hi-z st ate or low level when vdd is off power sequence timing value parameter min. max. units t1 0.5 10 t2 0 50 t3 200 - t4 200 - t5 0 50 t6 0 10 t7 500 - t8 10 - t9 0 180 t10 0 180 t11 10 - t12 0.5 10 ms www..net
22 of 30 au optronics corporation product specification b101ew05 v0 document version : 0.1 7. panel reliability test 7.1 vibration test test spec: test method: non-operation acceleration: 1.5 g frequency: 10 - 500hz random sweep: 30 minutes each axis (x, y, z) 7.2 shock test test spec: test method: non-operation acceleration: 220 g , half sine wave active time: 2 ms pulse: x,y,z .one time for each side 7.3 reliability test items required condition note temperature humidity bias ta= 40 , 90%rh, 300h high temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h high temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 250h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some perf ormance degradation allowed. self-recoverable. no data lost, no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a conf idence level 90% www..net
23 of 30 b101ew05 v0 document version : 0.1 8. mechanical characteristics 8.1 lcm outline dimension 8.1.1 standard front view www..net
24 of 30 b101ew05 v0 document version : 0.1 8.1.2 standard rear view & key components remark an d remind prevention damage the ic, connector, capacitor., w e recommend your design (ex: cable, rib, hardness p arts) far away those section those have remarked at this drawing. note: prevention ic damage, ic positions not allowe d any overlap over these areas. www..net
25 of 30 b101ew05 v0 document version : 0.1 9. shipping and package 9.1 shipping label format tbd www..net
26 of 30 b101ew05 v0 document version : 0.1 9.2 carton package the outside dimension of carton is tbd (l)mm x tbd (w)mm x tbd (h)mm 9.3 shipping package of palletizing sequence www..net
27 of 30 b101ew05 v0 document version : 0.1 10. appendix 10.1 edid description address function value value value note hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code d4 11010100 212 0b hex, lsb first 50 01010000 80 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 14 00010100 20 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 16 00010110 22 16 max v image size (rounded to cm) 0e 00001110 14 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) cb 11001011 203 1a blue/white low bits (lower 2:2:2:2 bits) 55 01010101 85 1b red x (upper 8 bits) 94 10010100 148 1c red y/ higher 8 bits 57 01010111 87 1d green x 53 01010011 83 1e green y 8e 10001110 142 1f blue x 27 00100111 39 20 blue y 23 00100011 35 21 white x 50 01010000 80 22 white y 54 01010100 84 www..net
28 of 30 b101ew05 v0 document version : 0.1 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 20 00100000 32 37 pixel clock/10000 usb 1c 00011100 28 38 horz active lower 8bits 00 00000000 0 39 horz blanking lower 8bits b8 10111000 184 3a horzact:horzblnk upper 4:4 bits 50 01010000 80 3b vertical active lower 8bits 20 00100000 32 3c vertical blanking lower 8bits 08 00001000 8 3d vert act : vertical blanking (upper 4:4 bit) 30 00110000 48 3e horzsync. offset 8 00001000 8 3f horzsync.width a 00001010 10 40 vertsync.offset : vertsync.width 31 00110001 49 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits d8 11011000 216 43 vertical image size lower 8bits 87 10000111 135 44 horizontal & vertical image size (upper 4:4 bits) 00 00000000 0 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 www..net
29 of 30 b101ew05 v0 document version : 0.1 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 a 60 manufacture 55 01010101 85 u 61 manufacture 4f 01001111 79 o 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 b 72 manufacture p/n 31 00110001 49 1 73 manufacture p/n 30 00110000 48 0 74 manufacture p/n 31 00110001 49 1 www..net
30 of 30 b101ew05 v0 document version : 0.1 75 manufacture p/n 45 01000101 69 e 76 manufacture p/n 57 01010111 87 w 77 manufacture p/n 30 00110000 48 0 78 manufacture p/n 35 00110101 53 5 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 v 7b manufacture p/n 30 00110000 48 0 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum cf 11001111 207 www..net

▲Up To Search▲

Price & Availability of B101EW05V0

	To Download B101EW05V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .